T-Series / Spring Loaded Automatic Tensioning
The Universal Drive Tensioner Spring loaded T-series incorporates an adjusting slot for control tensioning and a serrated arm, permitting tensioning at any point on a 360º arc.
The "T" Series tensioner has a spring for a constant tension which is more practical for pulsating loads. The base is more practical for pulsating loads. The base is made of high-grade semi-steel casting, incorporating a needle bearing and ball bearing to eliminate binding on over-hung loads. A precision cut gear and rack combined with a spring enables the arm to work 90º in either direction.
The standard model will support a 22# load at the idler shaft center. If more capacity is desired, a heavier spring is available to support up to 44# which pivots 45º in either direction.
| Model No. | Spring | Pivot Angle | Use with Shaft No.* | A | B | C | D | E | F | G | H | I | J | K | L | M | App. Wt. | Downloads | |||
| TM22 | 22lb (RED) |
90º Both Directions from Center |
SO2 | 1-1/2" | 2-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" |
4" |
3/8" |
4-13/16" |
6.37 | dwg | dxf | step | igs |
| TM22 | 22lb (RED) |
90º Both Directions from Center |
SO3 | 2-1/2" | 3-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" | 4" | 3/8" | 4-13/16" | 6.37 | dwg | dxf | step | igs |
| TM22 | 22lb (RED) |
90º Both Directions from Center |
SO4 | 3-1/2" | 4-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" | 4" | 3/8" | 4-13/16" | 6.37 | dwg | dxf | step | igs |
| TM44 | 44lb (GOLD) |
45º Both Directions from Center |
SO2 | 1-1/2" | 2-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" | 4" | 3/8" | 4-13/16" | 6.37 | dwg | dxf | step | igs |
| TM44 | 44lb (GOLD) |
45º Both Directions from Center |
SO3 | 2-1/2" | 3-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" | 4" | 3/8" | 4-13/16" | 6.37 | dwg | dxf | step | igs |
| TM44 | 44lb (GOLD) |
45º Both Directions from Center |
SO4 | 3-1/2" | 4-1/8" | 1" | 3" | 2-1/2" | 8-11/16" | 7-1/2" | 3-1/8" | 2-1/16" | 5" | 4" | 3/8" | 4-13/16" | 6.37 | dwg | dxf | step | igs |
*Idler shaft and set collar not included in tensioner unit. Must be ordered separately.